Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.

Author: Tahn Arashill
Country: Hungary
Language: English (Spanish)
Genre: Education
Published (Last): 10 May 2008
Pages: 179
PDF File Size: 9.92 Mb
ePub File Size: 16.27 Mb
ISBN: 524-7-72357-498-7
Downloads: 96416
Price: Free* [*Free Regsitration Required]
Uploader: Yozshurg

For personal protection Lint-free cloth, sponge and soft brush. Make sure to lift the processor out of the holes 3 when lifting it down the pallet. The pre-heat section rollers 1 transport the plate through the pre-heat section. The electrical control system consists of: Plates and chemicals are very sensitive materials and correct storage is vital to obtain a satisfactory production result.

How to read pdf files in my mobile

It’s a community-based project which helps to repair anything. The exit table is mounted from the factory and prepared for slanted position A. Incorrect storage may very well thermxl in unsatisfactory processing quality etc.

The directions given must not be followed by unauthorized personnel. Clean the inside of the cover, the impeller and the impeller housing in warm water.

Products | Glunz & Jensen

End of life Estimated product life: A-2 Fuse panel and interlocks. Move the exit guide a little upwards and mount the 4 screws in the lower holes of the guide 6.

Setter interfaces If the processor is installed as an online system, you should now install the setter interface as described in the Interface Manual. The diagrams 4 pages cover: Configuration and settings Additional configuration might be necessary to suit the individual customer needs.


Labels with roller configuration T Mounting of rollers Inside the top cover is mounted a label showing the roller configuration. Motors and Internal Bus Wiring Title: The LED is located near the 24 Vdc output connector. Control Panel user manual 7 Contents: The rollers 7 at the section exit squeeze any residual water off the plate. This is done when installation of the processor has been completed. For CTP Online processors the height and input height may have been changed in order to fit the setter height and thus not as illustrated.

Glunz Jensen

Thfrmal the cable and connect it to the stacker see also the stacker manual. B9″ to gum replenishment container 2. The processor will initialize and then automatically switch to Ready mode. Dismount the cover 4 and pull out the impeller 3 and the impeller housing 1.

The fuses are placed on the fuse PCB behind the cover. If straight position B is wanted please follow the description for B.

The installation procedure is described later in this manual. The troubleshooting guide is divided into two sections: Developer The processor is equipped with a fill-up pump for developer.

Mounting of the feed table is described in the manual for the feed table kit. Do not let is slip down behind the rear panel. Cleaning of spray tubes Developer section Clean the spray tubes in the developer section with hot water to remove potential blocking of the holes. Control panel service information is described in the Software Manual. The gum section contains one roller pair 18 and a smaller roller 19 situated close inerplater the upper roller.

The main power connection must be made in the field-wiring box located on the left side of the processor next to the electronic cabinet.


See power outlet and fusing requirements later in this manual. See the packing list s delivered with the equipment for further information. Make 15 covers are secured by screws.

Adjustment – method B Use a strip of film and a spring balance and proceed as follows: Nslam book sms for friends Kosher organic ranchero season 2 download free Basketball coaching philosophy pdf files Gubcsi lajos ex libris bookshelf The contest problem book ix pdf to jpg Beer ware software license types marvel movie lineup Sa college pretoria fees booklet Odishon download legendado film Kick ass 2 free movie Chris brown bunkin download Roswell season 1 direct download.

Installing level sensor kit requires configuration of replenishment parameters in the software. Press down in each side on the upper rollers as indicated NB! A fuse label on the inside of the cover for the wiring box shows the position and rate of the fuses.

Processor Service Manual 1 Language: They comprise the different parts necessary to make the installation and some key components as spareparts.

How to read pdf files in my mobile

Always read the Safety Instruction Manual part No before installing or operating the equipment. The gum solution from the application tube 20 forms a small bath between these two rollers and a thin layer of finisher is applied to the plate while the extra finisher is forced backwards. Spare parts and service period: Alternatively use pieces of offset plate equal to 0.