ASTM D4633 PDF

Designation: D − 10Standard Test Method for Energy Measurement for This test method is under the jurisdiction of ASTM Committee D18 on Soil and. Purchase your copy of ASTM D – 16 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available. ASTM D ,. “Standard. Test Method for Stress Wave. Energy Measurement for Dynamic. Penetrometer. Testing. Systems”. [2], speclfles.

Author: Faemi Aragore
Country: Japan
Language: English (Spanish)
Genre: Life
Published (Last): 25 September 2017
Pages: 180
PDF File Size: 4.52 Mb
ePub File Size: 5.73 Mb
ISBN: 725-6-61961-120-9
Downloads: 16541
Price: Free* [*Free Regsitration Required]
Uploader: Nizragore

The Standard Penetration Test is the most common d44633. The standard is now in your shopping cart. What is a standard? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations.

Reporting of test results in units other than SI asttm not be regarded as nonconformance with this test method.

ASTM D – 16 Standard Test Method for Energy Measurement for Dynamic Penetrometers

It is not intended for use with down-hole hammers. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the standard.

D44633 shopping cart is empty. In addition, they are representative of the significant digits that generally should be retained. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. Since the measured energy includes the extra potential energy effect due to the set per blow, tests for energy evaluation of the hammer systems should be limited to moderate N-value ranges between 10 and 50 Ref 7.

  ASTM 54A PDF

The quality of the result produced d44633 this standard is aastm on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Sustainable Development Goals and standardisation, how do they connect? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Subscribe on standards – Read more. This procedure may also be applicable to other dynamic penetrometer tests.

See also Refs 1- 6. Historical Version s – view previous versions of standard.

Valid Buy this standard. This procedure may also be applicable to other dynamic penetrometer tests. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.

Reliable results depend on many factors: Message to your colleague.

ASTM D4633 – 16

Practice D provides a means of evaluating some of those factors. It is not intended for use with down-hole hammers.

The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard. In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. Read more about SIS Subscriptions. The N-value depends on the soil properties but also on the mass, geometry, stroke, anvil, and operating efficiency of the hammer. Soil and Rock I: When you use our service you can be assured the latest editions and easy access.

  KECELARUAN PERSONALITI PDF

In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs. Engineering properties can be estimated on the basis of empirical correlations between N-values and soil density, strength or stiffness. General terms and conditions Cookies och Javascript Disclaimer Contact.

ASTM D – 16 – Standard Test Method for Energy Measurement for Dynamic Penetrometers

Contact us svenska Login. Please note that the selected standard is invalid. Report error on page. Alternatively, the N-value can be used directly in foundation design using correlations to design parameters such as allowable bearing pressure or pile capacity. Link to Active This link will always route to d463 current Active version of the standard.

This energy measurement procedure can evaluate variations of N-value resulting from differences in the hammer system. The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered standard. Users of this standard are cautioned that compliance with Practice D does not in itself assure reliable results.

Subscribe on standards with our subscription service.

Shopping cart Close cart 0, foreach: